Technical Data
1. Technical Data for SB Bonding Emulsion
- Technical data (of the pure synthetic liquid material)
| Technical Data | Value |
| Density of the fresh mortar |
1.85 kg/l |
| Compressive Strength (7days) | >20 N/mm2 |
| Compressive Strength (28 days) |
>35 N/mm2 |
| Flexural Tensile Strength (7 days) |
4.5 N/mm2 |
| Flexural Tensile Strength (28 days) |
5.5 N/mm2 |
| Adhesive Tensile Strength |
1.5N/mm2 |
| Waterproof against pressurised water
(positive and negative side) |
up to 13 bars |
| Coefficient of Water Vapour Diffusion Resistance |
60 |
| Pot Life |
approx. 2 hours |
| Resistant to Foot Traffic |
after approx. 2 days |
| Full Cure |
after approx. 2 weeks |
2. Technical Data for SB Bonding Emulsion
- Technical data (of the pure synthetic liquid material)
| Characteristic | Value |
| Dry matter content |
approx. 44 ± 1 % |
| pH-value | 10.5 – 11.5 |
| Viscosity |
approx. 120 mPa.s |
| Specific gravity |
approx. 1.00 |
| Elongation at break |
approx. 700 % |
| Breaking load | approx. 4.0 N / mm² |
| Application temperature |
+ 2 °C to + 35 °C |
3. Technical Data for KD System
-
Technical data
KÖSTER KD 1 Base
| Characteristic | Value |
| Density of the fresh mortar |
1.6kg / l |
| Compressive strength (7 days) |
>13 N/mm2 |
| Flexural tensile strength (7 days) |
>3.5 N/mm2 |
|
Setting time
(20 °C, 65 % relative humidity) |
approx. 15 min. |
KÖSTER KD 2
| Characteristic | Value |
| Setting time (when sealing in-rushes) |
approx. 20 sec. |
KÖSTER KD 3 Sealer
| Characteristic | Value |
| Density (20 °C) |
1.2 g / cm3 |
| Reaction time (20°C, 65 % relative humidity) |
2 - 3 hours |
KÖSTER KD-System
| Characteristic | Value |
| Waterproof against pressurised water |
up to 7 bar (negative side) |
4. Technical Data for KB Flex 200
- Technical data
| Characteristic | Value |
| Material basis |
Polyolefin |
| Colour |
grey |
| Specific gravity |
1.60 g/cm³ |
| Heat resistance |
max. + 50 °C |
| Consistency |
pasty, non-sagging |
| Application temperature | + 5 °C to + 35 °C |
| Substrate temperature |
+ 5 °C to + 30 °C |
5. Technical Data for KB Fix 5
- Technical data
| Characteristic | Value |
| Starts to set |
after approx. 5 minutes (20°C ) |
| Application of next layer |
after approx. 3 hours |
| Compressive strength: |
|
| - after 2 hours approx |
5 N / mm² |
| - after 1 day approx. |
15 N / mm² |
| - after 7 days approx. | 26 N / mm² |
| - after 28 days approx. |
34 N / mm² |
6. Technical Data for Repair Mortar Plus
- Technical data
| Characteristic | Value |
| Density of the fresh mortar |
1.8 kg / I
|
| Compressive strength after 7 days | >18N/mm2 |
| Compressive strength after 28 days |
> 35 N /mm2
|
| Flexural tensile strength after 7 days |
>4 N/mm2 |
| Flexural tensile strength after 28 days |
>6 N/mm2
|
| Pot life |
10-15min |
7. Technical Data for Polysil TG 500
- Technical data
| Characteristic | Value |
| Application temperature |
min. 5°C |
| Specific gravity |
1.03 g/cm³ |
| Surface |
transparent slightly sticky |
| Application of next layer: |
|
| - After 30 minutes |
cementitious building materials |
| - After 24 hours | acrylate and silicate paints |
Search
 |
|
(+61) 02 8336 1666 |
Members Only
